Foro de Soporte Técnico
https://gutl.jovenclub.cu/foro/
Aqui vemos que mi modem esta conectado en el puerto ttyS0 y el modelo es MT5656ZDX, entre otros datos de velocidad, y en el puerto ttyS1 el resultado es failed ya que no tengo otro modem puesto en ese puerto.root@huracan:/home/nelson# wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- OK
ttyS0<*1>: ATQ0 V1 E1 Z -- OK
ttyS0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyS0<*1>: Modem Identifier: ATI -- MT5656ZDX
ttyS0<*1>: Speed 4800: AT -- OK
ttyS0<*1>: Speed 9600: AT -- OK
ttyS0<*1>: Speed 19200: AT -- OK
ttyS0<*1>: Speed 38400: AT -- OK
ttyS0<*1>: Speed 57600: AT -- OK
ttyS0<*1>: Speed 115200: AT -- OK
ttyS0<*1>: Max speed is 115200; that should be safe.
ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S2 S3
Found a modem on /dev/ttyS0.
Modem configuration written to /etc/wvdial.conf.
ttyS0<Info>: Speed 115200; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
¿Quizás sea lspci el comando que estás buscando? Aunque también están lshw, dmidecode, y probablemente haya otros.fVckingmania.hell escribió:[...] realmente lo que necesito es un comando que me devuelva donde estan montado mis tarjetas PCI y recuerdo que hay uno que te dice todo lo PCI que esta conectado, pero no recurdo cual es [...]
Código: Seleccionar todo
landy@ubuntu:~$ sudo wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT8314949
--> Waiting for carrier.
ATDT8314949
BUSY
--> The line is busy. Trying again.
--> Sending: ATDT8314949
--> Waiting for carrier.
ATDT8314949
NO DIALTONE
--> No dial tone.
--> Disconnecting at...
Código: Seleccionar todo
landy@ubuntu:~$ sudo wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3
WvModem<*1>: Cannot get information for serial port.
ttySL0<*1>: ATQ0 V1 E1 -- OK
ttySL0<*1>: ATQ0 V1 E1 Z -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem
ttySL0<*1>: Speed 4800: AT -- OK
ttySL0<*1>: Speed 9600: AT -- OK
ttySL0<*1>: Speed 19200: AT -- OK
ttySL0<*1>: Speed 38400: AT -- OK
ttySL0<*1>: Speed 57600: AT -- OK
ttySL0<*1>: Speed 115200: AT -- OK
ttySL0<*1>: Speed 230400: AT -- OK
ttySL0<*1>: Speed 460800: AT -- OK
ttySL0<*1>: Max speed is 460800; that should be safe.
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Found a modem on /dev/ttySL0.
Modem configuration written to /etc/wvdial.conf.
ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
Código: Seleccionar todo
[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = 8314949
ISDN = 0
Username = myusername
Init1 = ATZ
Password = mypass
Modem = /dev/ttySL0
Baud = 460800
Carrier Check = no
Stupid Mode = yes
New PPPD = yes
Password Prompt = mypass