Grupo de Usuarios de Tecnologías Libres

Código: Seleccionar todo

--> WvDial: Internet dialer version 1.61
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATM1L3DT644XXXX
--> Waiting for carrier.
ATM1L3DT644XXXX
CONNECT 38400
--> Carrier detected.  Waiting for prompt.
Debian GNU/Linux ttyS4 38400 (38400)
**EMSI_REQA77E
[11]              
hulk-srv login: 
Debian GNU/Linux ttyS4 38400 (38400)
**EMSI_REQA77E
[11]              
hulk-srv login: 
--> Looks like a login prompt.
--> Sending: userXXX
userXXX
Password: 
--> Looks like a password prompt.
--> Sending: (password)
Last login: Fri Oct  7 02:11:25 CDT 2011 on ttyS4
Welcome to Ubuntu 11.04 (GNU/Linux 2.6.38-9-generic i686)
 * Documentation:  https://help.ubuntu.com/
You have new mail.
n
NO CARRIER
--> Connected, but carrier signal lost!  Retrying...
--> Sending: ATM1L3DT644XXXX
--> Waiting for carrier.
ATM1L3DT644XXXX
--> No Carrier!  Trying again.
--> Maximum Attempts Exceeded..Aborting!!
--> Disconnecting at Fri Oct  7 14:06:42 2011

Código: Seleccionar todo

# dialin.config (CNDFILE in policy.h)
#
# cndfile contains a series of tokens separated by newlines, commas, tabs
# and spaces.  The callerid number is compared with each token in turn,
# until a match occurs.  A match occurs when the token compares equally to
# the callerid information up to the length of the token.  If the token is
# prefixed with a "!", a match means "do not answer the phone".  The token
# "all" matches any telephone number, and will terminate scanning of the
# cndfile.  If no callerid number is present, it is assumed to have the
# value "none".  A line starting with "#" is a comment.  There is an
# implicit "all" at the end of the file.
# 
# For example:

# list of my friends' data lines
#3433535, 7445343, 5551212
#
# dad's fax
#4164646777
#
# disallow [other] calls from numbers matching the following prefix:
#!416
#
# disallow that speed dialer that keeps hitting my machine
#!3444444
#
# allow all calls with the following prefixes
#832, 555
#
# don't allow calls when there's no callerid:
#!none
#
# It's okay to accept calls from out of area
# ("OUT_OF_AREA" token seems ZyXEL specific)
#OUT_OF_AREA
# For V.253 compatibles modems "OUT OF AREA" is represented by the
# single letter 'O'
#O
#
# The caller has denied the transmission of his number
# (private service) (For German Telecom dialprefix *31#).
# This is for V.253 compatible modems represented by the single
# letter 'P'.
# don't allow access to my machine for those callers
#!P
# 
#
# disallow all other calls
#!all

Código: Seleccionar todo

# login.config
#
# This is a sample "login dispatcher" configuration file for mgetty
#
# Format:
#	username userid utmp_entry login_program [arguments]
#
# Meaning:
#       for a "username" entered at mgettys login: prompt, call
#	"login_program" with [arguments], with the uid set to "userid",
#	and a USER_PROCESS utmp entry with ut_user = "utmp_entry"
#
# username may be prefixed / suffixed by "*" (wildcard)
#
# userid is a valid user name from /etc/passwd, or "-" to not set
#  a login user id and keep the uid/euid root (needed for /bin/login)
#
# utmp_entry is what will appear in the "who" listing. Use "-" to not
#  set an utmp entry (a must for /bin/login), use "@" to set it to the
#  username entered. Maximum length is 8 characters.
#
# login_program is the program that will be exec()ed, with the arguments
#  passed in [arguments]. A "@" in the arguments will be replaced with the
#  username entered. Warning: if no "@" is given, the login_program has
#  no way to know what user name the user entered.
#
#
# SAMPLES:
# Use this one with my Taylor-UUCP and Taylor-UUCP passwd files. 
#  (Big advantage: tuucp can use the same passwd file for serial dial-in 
#   and tcp dial-in [uucico running as in.uucpd]). Works from 1.05 up.
#
#U*	uucp	@	/usr/sbin/uucico -l -u @

#
# Use this one for fido calls (login name /FIDO/ is handled specially)
#
# You need Eugene Crosser's "ifmail" package for this to work.
#  mgetty has to be compiled with "-DFIDO", otherwise a fido call won't
#  be detected.
#
#/FIDO/	uucp	fido	/usr/lib/fnet/ifcico @

#
# Automatic PPP startup on receipt of LCP configure request (AutoPPP).
#  mgetty has to be compiled with "-DAUTO_PPP" for this to work.
#  Warning: Case is significant, AUTOPPP or autoppp won't work!
#  Consult the "pppd" man page to find pppd options that work for you.
#
#  NOTE: for *some* users, the "-detach" option has been necessary, for 
#        others, not at all. If your pppd doesn't die after hangup, try it.
#
#  NOTE2: "debug" creates lots of debugging info.  LOOK AT IT if things
#         do not work out of the box, most likely it's a ppp problem!
#
#  NOTE3: "man pppd" is your friend!
#
#  NOTE4: max. 9 arguments allowed.
#
/AutoPPP/ - a_ppp /usr/sbin/pppd auth -chap +pap login debug 
#
#
# An example where no login name in the argument list is desired:
#  automatically telnetting to machine "smarty" for a given login name
#
#telnet-smarty	gast	telnet	/usr/bin/telnet -8 smarty
#
# This is the "standard" behaviour - *dont* set a userid or utmp
#  entry here, otherwise /bin/login will fail!
#  This entry isn't really necessary: if it's missing, the built-in
#  default will do exactly this.
#
*	-	-	/bin/login @

Código: Seleccionar todo

#
# mgetty configuration file
#
# this is a sample configuration file, see mgetty.info for details
#
# comment lines start with a "#", empty lines are ignored


# ----- global section -----
#
# In this section, you put the global defaults, per-port stuff is below


# set the global debug level to "4" (default from policy.h)
debug 4

# set the local fax station id
fax-id  

# access the modem(s) with 38400 bps
speed 38400

# use an alternate issue file, to avoid being bitten by linuxlogo
issue-file /etc/issue.mgetty

#  use these options to make the /dev/tty-device owned by "uucp.uucp" 
#  and mode "rw-rw-r--" (0664). *LEADING ZERO NEEDED!*
#port-owner uucp
#port-group uucp
#port-mode 0664

#  use these options to make incoming faxes owned by "root.uucp" 
#  and mode "rw-r-----" (0640). *LEADING ZERO NEEDED!*
#fax-owner root
#fax-group uucp
#fax-mode 0640


# ----- port specific section -----
# 
# Here you can put things that are valid only for one line, not the others
#

# Zoom V.FX 28.8, connected to ttyS0: don't do fax, less logging
#
#port ttyS0
#  debug 3
#  data-only y

# some other Rockwell modem, needs "switchbd 19200" to receive faxes
# properly (otherwise it will fail with "timeout").
#
#port ttyS1
#  speed 38400
#  switchbd 19200

# ZyXEL 2864, connected to ttyS2: maximum debugging, grab statistics
#
#port ttyS2
#  debug 8
#  init-chat "" \d\d\d+++\d\d\dAT&FS2=255 OK ATN3S0=0S13.2=1 OK 
#  statistics-chat "" AT OK ATI2 OK
#  statistics-file /var/log/statistics.ttyS2
#  modem-type cls2

# direct connection of a VT100 terminal which doesn't like DTR drops
# ("direct" meaning "*no* *modem*".  NEVER enable "direct yes" on modem lines!)
#
#port ttyS3
#  direct y
#  speed 19200
#  toggle-dtr n

Código: Seleccionar todo

# /etc/ppp/options
# 
# Originally created by Jim Knoble <jmknoble@mercury.interpath.net>
# Modified for Debian by alvar Bray <alvar@meiko.co.uk>
# Modified for PPP Server setup by Christoph Lameter <clameter@debian.org>
#
# To quickly see what options are active in this file, use this command:
#   egrep -v '#|^ *$' /etc/ppp/options

# Specify which DNS Servers the incoming Win95 or WinNT Connection should use
# Two Servers can be remotely configured 
ms-dns x.x.x.x
ms-dns x.x.x.x

# Specify which WINS Servers the incoming connection Win95 or WinNT should use
# ms-wins 192.168.1.50
# ms-wins 192.168.1.51

# Run the executable or shell command specified after pppd has
# terminated the link.  This script could, for example, issue commands
# to the modem to cause it to hang up if hardware modem control signals
# were not available.
#disconnect "chat -- \d+++\d\c OK ath0 OK"

# async character map -- 32-bit hex; each bit is a character
# that needs to be escaped for pppd to receive it.  0x00000001
# represents '\x01', and 0x80000000 represents '\x1f'.
asyncmap 0

# Require the peer to authenticate itself before allowing network
# packets to be sent or received.
# Please do not disable this setting. It is expected to be standard in
# future releases of pppd. Use the call option (see manpage) to disable
# authentication for specific peers.
#auth
noauth
# ... Unfortunately, fixing this properly in the peers file
# (/etc/ppp/peers/ppp0, typically) is apparently incompatible with the
# paradigm used by gnome-system-tools and system-tools-backend for
# managing the peers files.  So in Ubuntu Feisty we change the default.

# Use hardware flow control (i.e. RTS/CTS) to control the flow of data
# on the serial port.
crtscts

# Use software flow control (i.e. XON/XOFF) to control the flow of data
# on the serial port.
#xonxoff

# Specifies that certain characters should be escaped on transmission
# (regardless of whether the peer requests them to be escaped with its
# async control character map).  The characters to be escaped are
# specified as a list of hex numbers separated by commas.  Note that
# almost any character can be specified for the escape option, unlike
# the asyncmap option which only allows control characters to be
# specified.  The characters which may not be escaped are those with hex
# values 0x20 - 0x3f or 0x5e.
#escape 11,13,ff

# Don't use the modem control lines.
#local

# Specifies that pppd should use a UUCP-style lock on the serial device
# to ensure exclusive access to the device.
lock

# Don't show the passwords when logging the contents of PAP packets.
# This is the default.
hide-password

# When logging the contents of PAP packets, this option causes pppd to
# show the password string in the log message.
#show-password

# Use the modem control lines.  On Ultrix, this option implies hardware
# flow control, as for the crtscts option.  (This option is not fully
# implemented.)
modem

# Set the MRU [Maximum Receive Unit] value to <n> for negotiation.  pppd
# will ask the peer to send packets of no more than <n> bytes. The
# minimum MRU value is 128.  The default MRU value is 1500.  A value of
# 296 is recommended for slow links (40 bytes for TCP/IP header + 256
# bytes of data).
#mru 542

# Set the interface netmask to <n>, a 32 bit netmask in "decimal dot"
# notation (e.g. 255.255.255.0).
netmask 255.255.255.0

# Disables the default behaviour when no local IP address is specified,
# which is to determine (if possible) the local IP address from the
# hostname. With this option, the peer will have to supply the local IP
# address during IPCP negotiation (unless it specified explicitly on the
# command line or in an options file).
#noipdefault

# Enables the "passive" option in the LCP.  With this option, pppd will
# attempt to initiate a connection; if no reply is received from the
# peer, pppd will then just wait passively for a valid LCP packet from
# the peer (instead of exiting, as it does without this option).
#passive

# With this option, pppd will not transmit LCP packets to initiate a
# connection until a valid LCP packet is received from the peer (as for
# the "passive" option with old versions of pppd).
#silent

# Don't request or allow negotiation of any options for LCP and IPCP
# (use default values).
#-all

# Disable Address/Control compression negotiation (use default, i.e.
# address/control field disabled).
#-ac

# Disable asyncmap negotiation (use the default asyncmap, i.e. escape
# all control characters).
#-am

# Don't fork to become a background process (otherwise pppd will do so
# if a serial device is specified).
-detach

# Disable IP address negotiation (with this option, the remote IP
# address must be specified with an option on the command line or in
# an options file).
#-ip

# Disable IPCP negotiation and IP communication. This option should
# only be required if the peer is buggy and gets confused by requests
# from pppd for IPCP negotiation.
#noip

# Disable magic number negotiation.  With this option, pppd cannot
# detect a looped-back line.
#-mn

# Disable MRU [Maximum Receive Unit] negotiation (use default, i.e.
# 1500).
#-mru

# Disable protocol field compression negotiation (use default, i.e.
# protocol field compression disabled).
#-pc

# Require the peer to authenticate itself using PAP.
#+pap

# Don't agree to authenticate using PAP.
#-pap

# Require the peer to authenticate itself using CHAP [Cryptographic
# Handshake Authentication Protocol] authentication.
#+chap

# Don't agree to authenticate using CHAP.
#-chap

# Disable negotiation of Van Jacobson style IP header compression (use
# default, i.e. no compression).
#-vj

# Increase debugging level (same as -d).  If this option is given, pppd
# will log the contents of all control packets sent or received in a
# readable form.  The packets are logged through syslog with facility
# daemon and level debug. This information can be directed to a file by
# setting up /etc/syslog.conf appropriately (see syslog.conf(5)).  (If
# pppd is compiled with extra debugging enabled, it will log messages
# using facility local2 instead of daemon).
debug

# Append the domain name <d> to the local host name for authentication
# purposes.  For example, if gethostname() returns the name porsche,
# but the fully qualified domain name is porsche.Quotron.COM, you would
# use the domain option to set the domain name to Quotron.COM.
#domain <d>

# Enable debugging code in the kernel-level PPP driver.  The argument n
# is a number which is the sum of the following values: 1 to enable
# general debug messages, 2 to request that the contents of received
# packets be printed, and 4 to request that the contents of transmitted
# packets be printed.
#kdebug n

# Set the MTU [Maximum Transmit Unit] value to <n>. Unless the peer
# requests a smaller value via MRU negotiation, pppd will request that
# the kernel networking code send data packets of no more than n bytes
# through the PPP network interface.
#mtu <n>

# Set the name of the local system for authentication purposes to <n>.
# This is a privileged option. With this option, pppd will use lines in the
# secrets files which have <n> as the second field when looking for a
# secret to use in authenticating the peer. In addition, unless overridden
# with the user option, <n> will be used as the name to send to the peer
# when authenticating the local system to the peer. (Note that pppd does
# not append the domain name to <n>.)
#name <n>

# Enforce the use of the hostname as the name of the local system for
# authentication purposes (overrides the name option).
#usehostname

# Set the assumed name of the remote system for authentication purposes
# to <n>.
#remotename <n>

# Add an entry to this system's ARP [Address Resolution Protocol]
# table with the IP address of the peer and the Ethernet address of this
# system.
proxyarp

# Use the system password database for authenticating the peer using
# PAP. Note: mgetty already provides this option. If this is specified
# then dialin from users using a script under Linux to fire up ppp wont work.
# login

# If this option is given, pppd will send an LCP echo-request frame to the
# peer every n seconds. Normally the peer should respond to the echo-request
# by sending an echo-reply. This option can be used with the
# lcp-echo-failure option to detect that the peer is no longer connected.
lcp-echo-interval 30

# If this option is given, pppd will presume the peer to be dead if n
# LCP echo-requests are sent without receiving a valid LCP echo-reply.
# If this happens, pppd will terminate the connection.  Use of this
# option requires a non-zero value for the lcp-echo-interval parameter.
# This option can be used to enable pppd to terminate after the physical
# connection has been broken (e.g., the modem has hung up) in
# situations where no hardware modem control lines are available.
lcp-echo-failure 4

# Set the LCP restart interval (retransmission timeout) to <n> seconds
# (default 3).
#lcp-restart <n>

# Set the maximum number of LCP terminate-request transmissions to <n>
# (default 3).
#lcp-max-terminate <n>

# Set the maximum number of LCP configure-request transmissions to <n>
# (default 10).
#lcp-max-configure <n>

# Set the maximum number of LCP configure-NAKs returned before starting
# to send configure-Rejects instead to <n> (default 10).
#lcp-max-failure <n>

# Set the IPCP restart interval (retransmission timeout) to <n>
# seconds (default 3).
#ipcp-restart <n>

# Set the maximum number of IPCP terminate-request transmissions to <n>
# (default 3).
#ipcp-max-terminate <n>

# Set the maximum number of IPCP configure-request transmissions to <n>
# (default 10).
#ipcp-max-configure <n>

# Set the maximum number of IPCP configure-NAKs returned before starting
# to send configure-Rejects instead to <n> (default 10).
#ipcp-max-failure <n>

# Set the PAP restart interval (retransmission timeout) to <n> seconds
# (default 3).
#pap-restart <n>

# Set the maximum number of PAP authenticate-request transmissions to
# <n> (default 10).
#pap-max-authreq <n>

# Set the maximum time that pppd will wait for the peer to authenticate
# itself with PAP to <n> seconds (0 means no limit).
#pap-timeout <n>

# Set the CHAP restart interval (retransmission timeout for
# challenges) to <n> seconds (default 3).
#chap-restart <n>

# Set the maximum number of CHAP challenge transmissions to <n>
# (default 10).
#chap-max-challenge

# If this option is given, pppd will rechallenge the peer every <n>
# seconds.
#chap-interval <n>

# With this option, pppd will accept the peer's idea of our local IP
# address, even if the local IP address was specified in an option.
#ipcp-accept-local

# With this option, pppd will accept the peer's idea of its (remote) IP
# address, even if the remote IP address was specified in an option.
#ipcp-accept-remote

# Disable the IPXCP and IPX protocols.
# To let pppd pass IPX packets comment this out --- you'll probably also
# want to install ipxripd, and have the Internal IPX Network option enabled
# in your kernel.  /usr/doc/HOWTO/IPX-HOWTO.gz contains more info.
noipx

# Exit once a connection has been made and terminated. This is the default,
# unless the `persist' or `demand' option has been specified.
#nopersist

# Do not exit after a connection is terminated; instead try to reopen
# the connection.
#persist

# Terminate after n consecutive failed connection attempts.
# A value of 0 means no limit. The default value is 10.
#maxfail <n>

# Initiate the link only on demand, i.e. when data traffic is present. 
# With this option, the remote IP address must be specified by the user on
# the command line or in an options file.  Pppd will initially configure
# the interface and enable it for IP traffic without connecting to the peer. 
# When traffic is available, pppd will connect to the peer and perform
# negotiation, authentication, etc.  When this is completed, pppd will
# commence passing data packets (i.e., IP packets) across the link.
#demand

# Specifies that pppd should disconnect if the link is idle for <n> seconds.
# The link is idle when no data packets (i.e. IP packets) are being sent or
# received.  Note: it is not advisable to use this option with the persist
# option without the demand option.  If the active-filter option is given,
# data packets which are rejected by the specified activity filter also
# count as the link being idle.
#idle <n>

# Specifies how many seconds to wait before re-initiating the link after
# it terminates.  This option only has any effect if the persist or demand
# option is used.  The holdoff period is not applied if the link was
# terminated because it was idle.
#holdoff <n>

# Wait for up n milliseconds after the connect script finishes for a valid
# PPP packet from the peer.  At the end of this time, or when a valid PPP
# packet is received from the peer, pppd will commence negotiation by
# sending its first LCP packet.  The default value is 1000 (1 second).
# This wait period only applies if the connect or pty option is used.
#connect-delay <n>

# Packet filtering: for more information, see pppd(8)
# Any packets matching the filter expression will be interpreted as link
# activity, and will cause a "demand" connection to be activated, and reset
# the idle connection timer. (idle option)
# The filter expression is akin to that of tcpdump(1)
#active-filter <filter-expression>
192.168.1.200:192.168.1.201
# ---<End of File>---

Código: Seleccionar todo

#Client (User)      Server       Secret (password)         IP
userXXX                      *                      password                   *